Michael McNamara

technology, networking, virtualization and IP telephony

Motorola AP5131 and AP300 Hardware Revisions

by

Motorola logoThere was a recent hardware change to the Motorola AP5131 and AP300 which requires a specific version of software to operate properly. In the little information I’ve been able to dig up Motorola makes reference to a “Isotope HW” change. Anyone know what the that is?

In any event if you are ordering/deploying any new AP5131 or AP300s you’ll need to be mindful of this change and ensure that you are running the appropriate software releases and/or you have applied the specific patches.

You can find the release notes concerning the AP5131 right here.

You can find the release notes concerning the AP300 right here.

Cheers!

WISP/CAPWAP Protocol (Ethereal)

by

While writing the previous article I recalled all the problems I had trying to decode the Motorola (formerly Symbol) WISP, WISPe, CAPWAP protcool used between the Wireless LAN Switch and their Access Ports.

As of WireShark version 0.99.7 there is decode support for the Lightweight Access Point Protocol (LWAPP) protocol used by Airspace (Cisco) and a few other wireless vendors.

The legacy Motorola Wireless LAN WS5000, WS5100 switches (version 1.x and 2.x) utilize the WIreless Switch Protocol (WISP) while the Motorola Wireless LAN WS5100, RFS7000 (version 3.x and 1.x respectively) utilize the WIreless Switch Protocol Enhanced (WISPe). The WISPe protocol from Motorola very closely mimics the Control and Provisioning of Wireless Access Points (CAPWAP) that is currently being developed by the IETF.

Now that I’ve got that history lesson out of the way. Have you every needed to decode the protocol running between the Wireless Switch and the Access Ports?

As you know by now I have a large number of Motorola Wireless LAN switches and Access Ports deployed throughout my organization. Unfortunatley the latest version of WireShark does not support the decoding of WISP, WISPe, or CAPWAP.

Thankfully Ethereal v0.10.14 has decoders for the WISP and CAPWAP protocols. I will say this warning though. I have downloaded multiple copies of Ethereal v0.10.14 and some seem to support WISP and CAPWAP while others don’t appear to support it. If I find a link for a working version I’ll update this article.

Here’s an example of the WISP protocol between a Motorola Wireless LAN Switch (WS5000 v2.x) and an Access Port 300 (AP300). (click on the image to enlarge it)

In the above trace you can see that the AP300 has just been reset and is in the process of booting. It starts by issuing EAPOL and LLDP packets before sending it’s first WISP “Hello”. You can see that the WS5000 responds to the “Hello” with a “Parent” command after which the Ap300 starts to download its runtime software with the “LoadMe” command.

Here’s an example of the CAPWAP protocol between a Motorola Wireless LAN Switch (WS5100 v3.x) and an Access Port 300 (AP300). (click on the image to enlarge it)

Note: this trace was not performed at the port level so we don’t see the EAPOL or LLDP traffic. We can see the AP300 making “Discovery”, “Join” and “Cfg” requests of the WS5100 switch.

Cheers!

UPDATE: March 29, 2008

Here’s a link for Ethereal v0.10.14 that I believe should decode both WISP and CAPWAP;

http://www.michaelfmcnamara.com/files/wisp-ethereal-setup-0.10.14.exe

Layer 3 Access Port Adoption

by

The release of v3.x software for the Motorola WS5100 and v1.x software for the Motorola RFS7000 finally supports the deployment of Layer 3 Access Ports (APs that could be deployed across a Layer 3 network as opposed to those that can only be deployed across a Layer 2 network).

The latest release of firmware for the AP300 will first attempt to locate a wireless switch for adoption via a Layer 2 broadcast request. If it’s unable to locate a wireless switch it will make a DHCP request for an IP address. If the DHCP response does not include option 189 (string) it will make a DNS request to try and locate the wireless switch.

There are two ways the Access Port can locate the Wireless LAN Switch (WS5100/RFS7000) in Layer 3 mode;

  • DHCP Option
  • DNS Query

You can use DHCP and configure option 189 (string) with the IP address of the Motorola Wireless LAN Switch. You should note that you may need to enclose the string in quotation marks depending on your DHCP server software.

You can also create a DNS alias which the AP can use to locate the switch through a DNS query. The default DNS name requested by an AP300 is “Symbol-CAPWAP-Address”.

You might also notice that the AP300 will also support LLDP (802.1ab) if your Ethernet switch supports it.

Cheers!

Update: August 27, 2008
I should point out that you may need to “prime” the AP300 with the latest firmware by connecting it to a WS5100/RFS7000 over a Layer 2 network. If the AP300 has an older firmware it won’t be able to connect up over a Layer 3 network so you may need to connect it over a Layer 2 network first to allow the AP300 to upgrade after which you’ll be able to connect it over a Layer 2/3 network. The AP300 will automatically upgrade once it connects to the WS5100/RFS7000, there’s nothing that needs to be done by the user or administrator. The WS5100/RFS7000 will need to be running v3.x or v1.x respectively.

Cheers!

Recent Posts

Categories

SUBSCRIBE BY EMAIL