Comments on: Motorola AP5131 and AP300 Hardware Revisions https://blog.michaelfmcnamara.com/2010/03/motorola-ap5131-and-ap300-hardware-revisions/ technology, networking, virtualization and IP telephony Sat, 20 May 2017 13:05:42 +0000 hourly 1 https://wordpress.org/?v=6.7.2 By: Michael McNamara https://blog.michaelfmcnamara.com/2010/03/motorola-ap5131-and-ap300-hardware-revisions/comment-page-1/#comment-80942 Sat, 20 May 2017 13:05:42 +0000 http://blog.michaelfmcnamara.com/?p=1302#comment-80942 In reply to Alexey.

Hi Alexey,

Sorry I don’t have any software for the 5131 hanging around. You might have luck seeking out a Symbol/Motorola/Zebra/Extreme sales engineer and see if they’ll help you out.

Good Luck!

]]> By: Alexey https://blog.michaelfmcnamara.com/2010/03/motorola-ap5131-and-ap300-hardware-revisions/comment-page-1/#comment-80914 Thu, 18 May 2017 16:24:42 +0000 http://blog.michaelfmcnamara.com/?p=1302#comment-80914 Hello!

My “Ap 5131 dual radio dependent” requires firmware version no higher than 3.4.0
The one that we have, apparently was installed by mistake and works incorrectly. (6.3.0)

Can you help me?!
I will be very grateful for any version, even very old, you can send here: bornzoo@mail.ru

]]> By: Michael McNamara https://blog.michaelfmcnamara.com/2010/03/motorola-ap5131-and-ap300-hardware-revisions/comment-page-1/#comment-6023 Wed, 01 Feb 2012 00:28:45 +0000 http://blog.michaelfmcnamara.com/?p=1302#comment-6023 In reply to santhosh.

Hi Santhosh,

The AP300 is a dependent Access Port that requires a Motorola Wireless LAN Switch to operate. If you are running an older version of software on the Wireless LAN Switch you need to install a patch (refer to the post above) in order to support a new hardware release of the AP300.

Cheers!

]]> By: santhosh https://blog.michaelfmcnamara.com/2010/03/motorola-ap5131-and-ap300-hardware-revisions/comment-page-1/#comment-6021 Tue, 31 Jan 2012 12:41:04 +0000 http://blog.michaelfmcnamara.com/?p=1302#comment-6021 i couldnt get what you are saying. what installation did we need. please tell me the software.
there is no switch for my device AP300

]]> By: Michael McNamara https://blog.michaelfmcnamara.com/2010/03/motorola-ap5131-and-ap300-hardware-revisions/comment-page-1/#comment-1853 Fri, 12 Mar 2010 14:25:12 +0000 http://blog.michaelfmcnamara.com/?p=1302#comment-1853 In reply to Ray.

Hi Ray,

The installation of the patch isn’t too difficult at all. It should take just a few minutes, however, it does require a reboot of the Wireless LAN Switch.

Thanks for the comment and good luck with your Trapeze deployment!

]]> By: Ray https://blog.michaelfmcnamara.com/2010/03/motorola-ap5131-and-ap300-hardware-revisions/comment-page-1/#comment-1846 Wed, 10 Mar 2010 17:27:36 +0000 http://blog.michaelfmcnamara.com/?p=1302#comment-1846 This just bit us as we ordered some AP-300’s to use as replacements for failed units and the controllers would not accept them. The controller would see the AP but it would never associate. We are using WS5000 and WS5100. We would have to do both code updates and patches on our controllers…but we are in the process or replacing the equipment with Trapeze so I think we will try to limp long by taking AP’s from areas that do not need coverage.

]]>