Comments on: User Interface Button (UI Button) https://blog.michaelfmcnamara.com/2009/07/user-interface-button-ui-button/ technology, networking, virtualization and IP telephony Sat, 30 Oct 2021 14:55:51 +0000 hourly 1 https://wordpress.org/?v=6.8.3 By: Michael McNamara https://blog.michaelfmcnamara.com/2009/07/user-interface-button-ui-button/comment-page-1/#comment-100087 Sun, 08 Jul 2018 16:59:38 +0000 http://blog.michaelfmcnamara.com/?p=876#comment-100087 In reply to Scott.

Where is that command Scott?

I would assume that it just resets the stack process.

Cheers!
Mike

]]> By: Scott https://blog.michaelfmcnamara.com/2009/07/user-interface-button-ui-button/comment-page-1/#comment-98437 Mon, 25 Jun 2018 20:57:23 +0000 http://blog.michaelfmcnamara.com/?p=876#comment-98437 I know this is a rather old post, but hopefully you’ll see it anyway… I’m looking for clarification on the “Resetting a stack” process. Will that just initiate a warm reboot, or will it reset the stack to factory default values?

Thanks!

]]> By: Michael McNamara https://blog.michaelfmcnamara.com/2009/07/user-interface-button-ui-button/comment-page-1/#comment-2902 Wed, 24 Nov 2010 20:59:53 +0000 http://blog.michaelfmcnamara.com/?p=876#comment-2902 In reply to Shaun.

Hi Shaun,

The ASCII configuration generator (ACG) doesn’t seem to support the UI option. You can check the configuration with the command “show ui-button”. The setting is stored in the configuration but the ACG doesn’t support exporting this option to ASCII.

Avaya switches traditional store their configuration in a binary format… the ACG was written to provide an ASCII version of that binary configuration. Unfortunately there are several features/options which the ACG doesn’t support so they don’t appear in the ASCII configuration (show running-config).

Cheers!

]]> By: Shaun https://blog.michaelfmcnamara.com/2009/07/user-interface-button-ui-button/comment-page-1/#comment-2901 Wed, 24 Nov 2010 20:39:01 +0000 http://blog.michaelfmcnamara.com/?p=876#comment-2901 I’ve issued the command “no ui-button enable” on a stack of 5520s/5510 but I do not see this reflected in the ASCII Configuration. Are you experiencing the same thing? Currently I do not have any on-shelf spares to test this with (scary!). I’m wondering how the stack retains this setting if is is not showing up in the ASCII Configuration.

]]> By: Michael McNamara https://blog.michaelfmcnamara.com/2009/07/user-interface-button-ui-button/comment-page-1/#comment-1081 Fri, 31 Jul 2009 13:31:17 +0000 http://blog.michaelfmcnamara.com/?p=876#comment-1081 In reply to Chris (Nortel ER).

It’s the typical… user in closet unwittingly starts pushing button causing outage to very high profile stack of 5500 series switches. Thankfully they only caused the stack to reboot and didn’t reset the management IP address.

I personally only learned of the user interface button a few month ago from a work colleague.

There’s always something new to learn!
Cheers!

]]> By: Chris (Nortel ER) https://blog.michaelfmcnamara.com/2009/07/user-interface-button-ui-button/comment-page-1/#comment-1077 Fri, 31 Jul 2009 04:08:04 +0000 http://blog.michaelfmcnamara.com/?p=876#comment-1077 What happened? Which led you to write about the “UI button”

]]>