It took me all of 15 seconds to find the link on Avaya’s website.

ftp://ftp.avaya.com/incoming/Up1cku9/tsoweb/www142.nortelnetworks.com/software/j/jdm/6.x/

sir i need JDM for configuring nortel 425 baystck switches pls tell me where i can downlaod this.

Hi Rashid,

You can initiate a TFTP backup via JDM then you can follow the following blog post to initiate a factory reset;

http://blog.michaelfmcnamara.com/2007/11/factory-reset-nortel-ethernet-switch/
http://blog.michaelfmcnamara.com/2007/12/factory-reset-nortel-ethernet-routing-switch/

Good Luck!

I have Nortel switch (Baystack 470 24T) and (Passport 1612g).
I want to take the backup of these switches (.bin) files.
1- How to take the backup of these switches configuration through java device manager.
or through telnet. (Steps)
2- I can access above two switches through java device manager but i don’t have the Password for these switches.
3- How to Reset the above switches
4- Bydefault password of the javadevice manager and above nortel switches

regards

Rashid

Hi Sep,

This topic has already been discussed on the forums;

http://forums.networkinfrastructure.info/nortel-ethernet-switching/monitor-cpu-and-memory-5530-4550t-via-snmp/

Good Luck!

I am looking for system oids for cpu/mem utilization on Nortel 470-48t switches. Google is your friend, but sometimes it isn’t easy to find.
Can you help on that?

Thanks in advance.

Sep

Hi Azi,

You now need to use either Enterprise Device Manager (EDM) or Avaya’s management product Configuration and Orchestration Manager (COM).

No additional development is being done with JDM.

Thanks,
Mike

Just want to know , is there any other alternative than JDM that could be use on VSP-9000?

That’s a different model of switch and has a different OID. I should also warn you that the SNMP OID for CPU and memory utilization is only available when running 6.x software on the ERS 5000 series switch. I don’t recall the exaxt OID right now but you can find it by performing a packet trace of Device Manager, Edit -> Chassis -> Chassis -> CPU/Mem Utilization. I believe it’s somewhere around 1.3.6.1.4.1.45.1.6.3.8.1.1.x

Good Luck!

Hello and thanks for the response!
I’m trying to monitor 5510-5530; isn’t that variable the one to check? I read that somewhere else

Hi Ale,

The OID that you reference above is for the Ethernet Routing Switch 1600 and 8600 switches. What model switch are you trying to monitor?

Good Luck!

Got a question, I need to monitor the CPU utilization in a Nortel Switch, I know that the SNMP variable to monitor is ‘rcSysCpuUtil’. Now, what if my device doesn’t have the respective OID (1.3.6.1.4.1.2272.1.1.20.0)? is there anything I can do?

for the record if you are using SNMPv2 you can use these switches

-out -trace -rd -wr -trapPort -trapLog -sysLog -socket -proxy -cacheServer

Hi Jorge,

What version of Java Device Manager are you using? You probably need to upgrade JDM to the latest release.

Cheers!

Hi Davy.

Thansk a lot for the info

I am using the firmware 3.7.2.12 in the 470-48T (No Problem) and 5.3.0.3 on the 4548GT-PWR (The message appear).

Sorry I will use the forums instead…

Thanks
Jorge

The latest switch firmware does not support JDM, you must use EDM instead.

Also, the forums would be a better place for this quesion :-)

I am having a problem let say with the JDM each tim ethat I launch the application it shows me a window that says. “YOU ARE ATTEMPTING TO USE AN OLDER VERSION OF JDM CODE WITH A NEWER VERSION OF SOFTWARE CODE FOR THIS DEVICE YOU ARE MANAGING. PLEASE VISIT NORTEL.COM TO GET LATEST JDM SOFTWARE”. but I am using the version 6.2.1.3 that it is suppose that is the latest one. Can any one help me to solve this?

Regards
Jorge

Hi Ashok,

Your question isn’t really topic for the post “Nortel Java Device Manager Tips”. You need to investigate traffic filters. You can post your question over in the discussion forums and I’m sure someone will respond.

Cheers!

I wants Vlan 15 should communicate only with 172.16.16.11. & block all other connection from Vlan 15.

Guide me configure with device manager and CLI

Thank you for the response actually i am using the ERS 8600 but not with the 7.0 software release. i will browse through some documentation but at first i had a hard time researching and wanted to make sure it would be possible. I hope it is.

Thank you.

Hi Thallium,

The answer is going to depend on a number of variables include what model of switch and what software release. The last time I looked authenticating SNMPv3 sessions via RADIUS/TACACS+ was not yet supported on the Ethernet Routing Switch 8600, 5000,4500,2500.

I’m not sure but I would be surprised if this is not supported in software release 7.0 for the ERS 8600.

I would suggest you have a look at the document below. It may be slightly dated but it should provide you enough information to get you started.

2008_03_26_Authentication_Authorization_and_Accounting_for_ERS_and_ES_TCG_NN48500558.pdf

Good Luck!

i am a beginner at this, any ideas how i can authenticate the JDM session…? trying to use Active Directory Username and password….

Thanks

Hi db_nortel,

You can use SNMP to poll the switch and create your own graphs.

.iso.org.dod.internet.private.enterprises.rapidCity.rcMgmt.rcSystem.rcSysCpuUtil.0
.1.3.6.1.4.1.2272.1.1.20.0

Good Luck!

Hi Mick,

I’ve never done it myself… so I can’t say.

Good Luck!

I use ESM 6.3.0 and i want have a estadistics of the cpu consuption.
With JDM i can viewing CpuUtil(%) a graphic from performnace in real time but only with window de 3 min and 20 seg.

Somebody knows how can capture data of the window JDM,”Graph Chasis System, CpuUtil”? For playback on a graphic historic the performance of the CPU.