Comments on: Motorola WS5100 and RFS7000 Software Update https://blog.michaelfmcnamara.com/2009/02/motorola-ws5100-and-rfs7000-software-update/ technology, networking, virtualization and IP telephony Wed, 04 May 2011 16:43:08 +0000 hourly 1 https://wordpress.org/?v=6.7.2 By: Michael McNamara https://blog.michaelfmcnamara.com/2009/02/motorola-ws5100-and-rfs7000-software-update/comment-page-1/#comment-4237 Wed, 04 May 2011 16:43:08 +0000 http://blog.michaelfmcnamara.com/?p=671#comment-4237 In reply to Betty.

The default baud rate of the console port is 19200. Do you have the correct baud rate configured?

If you suspect the hardware is bad you can RMA the switch to Motorola for depot repair.

Good Luck!

]]> By: Betty https://blog.michaelfmcnamara.com/2009/02/motorola-ws5100-and-rfs7000-software-update/comment-page-1/#comment-4236 Wed, 04 May 2011 16:22:57 +0000 http://blog.michaelfmcnamara.com/?p=671#comment-4236 Hi Michael,
The status LEDs are:
SYS 1 Flashing green
SYS 2 Off
Fan Blinking Green
Temperature Blinking Green
This is the console output

This is the console output

…~….
…þ….

not run the auto-rollback
:)

]]> By: Michael McNamara https://blog.michaelfmcnamara.com/2009/02/motorola-ws5100-and-rfs7000-software-update/comment-page-1/#comment-4229 Wed, 04 May 2011 01:43:47 +0000 http://blog.michaelfmcnamara.com/?p=671#comment-4229 In reply to Betty).

Hi Betty)

I used Google Translate on your comment and came out with the following; “RFS6000 I have a firmware update attempt that gave an error and restart, now I can not access it from Hyperterminal, any help?”

You get nothing from the serial console? Nothing at all? The RFS6000 has an auto-rollback feature and should rollback to the previously loaded software if there’s a problem booting the current software. If you can post the output from the serial console perhaps I can help further.

Good Luck!

]]> By: Betty) https://blog.michaelfmcnamara.com/2009/02/motorola-ws5100-and-rfs7000-software-update/comment-page-1/#comment-4220 Tue, 03 May 2011 21:02:10 +0000 http://blog.michaelfmcnamara.com/?p=671#comment-4220 Tengo un RFS6000 que al intentar actualizar Firmware dio un error y se reinicio, ahora no puedo accesarlo por Hyperterminal, alguna ayuda?

]]> By: Michael McNamara https://blog.michaelfmcnamara.com/2009/02/motorola-ws5100-and-rfs7000-software-update/comment-page-1/#comment-990 Mon, 29 Jun 2009 22:26:53 +0000 http://blog.michaelfmcnamara.com/?p=671#comment-990 In reply to Cipri.

Hi Cipri,

Your asking for a lot of information there friend. You only need to connect the AP300 to the same Layer 2 network as the WS5100 from a logical networking perspective. After that you’ll need to properly configure the WS5100 for the WLAN settings you want, the security settings, the radio configurations, etc. I would suggest that you visit the Motorola website and download the specific product manuals. Please keep in mind that there are significant differences between the 2.x and 3.x software branches.

Good Luck!

]]> By: Cipri https://blog.michaelfmcnamara.com/2009/02/motorola-ws5100-and-rfs7000-software-update/comment-page-1/#comment-983 Fri, 26 Jun 2009 12:27:33 +0000 http://blog.michaelfmcnamara.com/?p=671#comment-983 Hy ,
I have to configure an ws5100 with AP300 acces points.Could you please give me an tutorial how can i install him.
I have tried many times….but the problem is now that the AP300 have an bad signal(only10%).
Please give me an full tutorial ,if you have, how to configure an ws5100 with AP300.

Thanks in advance!

]]>